Audi 80/90/Coupe + 1.2. Car identification + 2. Engines, carburetors
3. Greasing system + 4. Cooling system + 5. Fuel system + 6. Exhaust system + 7. Ignition system + 8. Transmission + 9. Suspension brackets, wheels + 10. Brake system - 11. Steering 11.2. Shaft and casing of a steering column 11.3. A power absorbing steering column 11.4. Steering drive 11.5. Pipeline of high pressure / return pipeline 11.6. Adjustment of a free wheeling of a lath of a steering 11.7. Maple belt + 11.8. System of hydrostrengthening of a steering + 12. Body, salon + 13. Central air + 14. Electric equipment
|
Steering column
1. Washer 2. 35 N of m. 3. Shaft of a steering column establish against the stop in a casing of a steering column establish a shaft so that it went freely 4. A lock bolt, always replace 5. Gear wheel of a shaft of a steering column 6. Limiter 7. A tube with flanges it is put on a gear wheel of a shaft of a steering column and fastens bolts to the limiter 8. 25 N of m, always replace 9. 20 N of m, always replace 10. Lock of a steering column 11. A bolt with a head under a face key. Inhaling moment: 7 N of m. remove / establish by means of a usual natural a face head |
12. Lock washers always replace for removal: accurately grind off, then remove by means of a screw-driver 13. The spring, is established on a shaft of a steering column 14. Casing of a steering column consists of the top and bottom parts is on sale as the spare part with the established bearings do not subject it to temperature influence above 100 ° With and do not use greasing or solutions (can weaken connection between the top and bottom parts) address with a casing carefully and do not use a hammer at work with it 15. Washer 16. Fixing arm |
Prevention
Washers are established with a preliminary tightness. Do not get burns from the sparks flying at grinding of washers. If it is necessary, close the dashboard and a windscreen.
The top and bottom parts of a casing of a steering column are marked with red points. Always replace a casing of a steering column if the red point is ground off or it was erased. Shaft of a steering column and casing of a steering column, removal / installation
PERFORMANCE ORDER |
1) disconnect a wire of the negative plug of the accumulator |
2) remove the lower left part of the dashboard |
3) remove a steering wheel |
|
4) remove the block of switches of a steering column together with the furnish panel |
|
5) remove screws of fastening of an instrument guard (are specified by shooters) |
6) disconnect the connection socket from the ignition lock |
7) remove a bolt with a head under a face key |
8) ткрутите a casing of a steering column from a fixing arm |
|
9) remove the lock of a steering column from a steering column (it is specified by an arrow) |
10) lower a shaft and a casing of a steering column down so that they could be got from below an instrument guard |
|
Installation
PERFORMANCE ORDER |
1) insert a shaft of a steering column into a casing |
2) insert a steering column into an opening under an instrument guard and lift it |
3) put the lock of a steering column on a steering column |
4) establish a bolt with a head under a face key (it is specified by an arrow) |
5) insert a key into the ignition lock |
6) unlock the lock of a steering column that it was possible to turn a shaft of a steering column |
7) establish a bolt of fastening of a steering column |
8) connect together the limiter, a tube to flanges and a shaft of a steering column |
9) establish a steering column on the center, having moved it up and down on a fixing arm so that the connecting disk (on a tube with flanges) moved freely at rotation of a steering wheel |
10) tighten bolts of fastening of a steering column to a fixing arm |
11) connect the connection socket to the ignition lock |
12) establish an instrument guard |
13) establish the block of switches of a steering column |
14) establish a steering wheel |
15) connect a wire of the negative plug of the accumulator |
16) check operation of the block of switches of a steering column |
|
When wheels stand directly, the crossbeam of a steering wheel should is in horizontal situation.
Prevention
For prevention of injuries or refusal of an airbag of safety, dismantling, assembly and service of system of an airbag of safety it should be carried out only by the qualified mechanic.
Always disconnect power supply from safety cushion system at carrying out the repair work including removal of any elements of system of a safety cushion.
Since 1990, all Audi-80/90/cars of the Compartment are equipped with an airbag of the safety established on a steering wheel. At work with airbag of safety and elements of a steering which mention safety cushion system, it is necessary to observe certain precautionary measures.
Do not try to straighten elements of the mechanism of a steering or to carry out on them welding repair work.
Replace everything самоконтрящиеся nuts and bolts.
Since 1990, all Audi-80/90/cars of the Compartment are equipped with a power absorbing steering column, and also a safety airbag. |
|