Audi 80/90/Coupe

since 1986-1991 of release

Repair and car operation

Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburetors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
- 11. Steering
   11.2. Shaft and casing of a steering column
   11.3. A power absorbing steering column
   11.4. Steering drive
   11.5. Pipeline of high pressure / return pipeline
   11.6. Adjustment of a free wheeling of a lath of a steering
   11.7. Maple belt
   + 11.8. System of hydrostrengthening of a steering
+ 12. Body, salon
+ 13. Central air
+ 14. Electric equipment


11.4. Steering drive


Steering drive

1. Steering transfer
establish precisely on the center of a shaft of a steering column
establish steering transfer so that there were no distortions and a tension
if it is necessary, move it
it is a little in fastening places
2. Arm of cross-section draft
at an inhaling of nuts of fastening of cross-section bent for to an arm, the car should stand on the earth
3. 45 N of m, always replace
4. 45 N of m, always replace
5. Washer
6. Pipelines of a high pressure. Moment of an inhaling of fastening: 50 N of m.
establish a shlangovy clip on
inlet hose before removal
7. 20 N of m, always replace
8. Washer
9. Wheel casing
10. A bolt with a head under a face key
tighten before an inhaling of bolts of fastening of steering transfer to the body panel
11. Spring washer
12. Cover
do not remove from the body panel at removal of steering transfer
establish accurately in a round flute on a casing of the main gear wheel
13. A bolt, always replace
14. A connecting disk remove from a leading gear wheel together with a tube with flanges
15. 25 N of m, always replace
16. Body panel
17. Return pipeline
18. Sealing rings, always replace
19. "Banjo" bolt
inhaling moment: 40 N of m.
before untwisting, establish a shlangovy clip on the return pipeline

Steering drive (release models till January, 1989 of release)

1. Cover
it is possible to replace, without removing the reechny steering mechanism
2. Lock ring
put on a steering lath against the stop
establish a cover on a flute,
passing on a ring circle
3. 20 N of m.
4. Cover
5. Sealing ring *
always replace
6. Epiploon plug
it is established by thicker end up
7. Toddler
the flute is turned to a cover
8. Case of a lath of a steering
if the surface of the case is damaged in an installation site of a gear washer, accurately eliminate damage before installation of an epiploon of a lath
9. Steering lath
check a lath on existence of scratches round an epiploon installation site
10. Cap
inhaling moment: 50 N of m.
tighten by means of two center punches established at an angle in 180 ° to each other

11. Basic кольцо*
always replace
it is established on a cap
12. Sealing ring *, 44x2.5 mm
always replace
it is established on a cap
13. Sealing ring *, 42x2 mm
14. A sealing ring *, always replace
15. Washer
16. Needle bearing
17. Washer
18. Leader шестерня*
19. Epiploon
20. 20 N of m.
21. Casing of a leading gear wheel
22. Ball-bearing
23. Sealing ring
always replace
24. Spring
it is inserted into the slider
25. Ring
26. Epiploon of a lath of the helmsman управления*
27. Lock ring
check correctness of installation
28. Gear washer
check correctness of installation
29. Collar
use a collar which is pulled together by means of the screw, the screw should be turned to a body

The system of hydrostrengthening of a steering is filled with hydraulic liquid, G 002 000 detail. All elements marked with an asterisk, are included in a repair kit and should be replaced during repair.


Moisten all epiploons in hydraulic liquid before installation.

Do not try to straighten elements of a steering or to carry out on them repair welding work.

Works with a drive of a steering should be carried out on a pure workplace and all elements should contain in absolute purity.