Audi 80/90/Coupe

since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburetors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
- 11. Steering
   11.2. Shaft and casing of a steering column
   11.3. A power absorbing steering column
   11.4. Steering drive
   11.5. Pipeline of high pressure / return pipeline
   11.6. Adjustment of a free wheeling of a lath of a steering
   11.7. Maple belt
   - 11.8. System of hydrostrengthening of a steering
      11.8.1. Technical characteristics
      11.8.2. Pumping / filling of hydraulic liquid
      11.8.3. Check on tightness (at the working engine)
      11.8.4. Steering transfer
      11.8.5. Pump of the hydraulic booster of a steering (Vickers)
+ 12. Body, salon
+ 13. Central air
+ 14. Electric equipment


dfe5d7b3



11.8. System of hydrostrengthening of a steering

GENERAL INFORMATION

The pump of the hydraulic booster of a steering for 4-cylinder models

1. 20 N of m.
2. Arm
3. 20 N of m, always replace
4. Arm
5. 20 N, m.
6. Arm
7. 20 N of m.
8. Maple belt, size: 9.5 х850 mm
9. Bolt and fixing nut
10. 20 N of m.
11. A pulley, establish a mark "5Z" forward
12. 25 N of m.
13. 20 N of m.
14. Lopastny pump
before installation fill soaking-up part with hydraulic liquid and повращайте the pump that liquid began to leave the target channel
15. "Banjo" bolt, inhaling moment: 50 Km
16. Sealing ring
always replace
17. A soaking-up hose
18.
19. "Banjo" bolt, inhaling moment: 50 N of m.
20. Hose of a high pressure
21. Arm
22. 20 N of m.

The pump of the hydraulic booster of a steering for 5-cylinder models

1. "Banjo" bolt
inhaling moment: 50 N of m.
2. Sealing ring
always replace
3. 20 N of m.
4. Arm
5. Arm
6. Maple belt
size: 12.5x992мм
7. 20 N of m.
8. Pulley
establish a mark "5Z" forward
9. 20 N of m.
10. Tension device
11. 20 N of m.
12. Самоконтрящаяся nut
inhaling moment: 20 N of m.
13. Pump of the hydraulic booster of rulevy management
before installation fill soaking-up part with hydraulic liquid and повращайте the pump that liquid began to leave the target channel
14. Arm
15. Tube of a high pressure
16. Sealing ring
always replace
17. "Banjo" bolt, inhaling moment: 45 Nanometers.
18. A soaking-up hose
19. 20 N of m.
20. Sealing ring

Tank of the hydraulic booster of a steering


1. Hose of the return pipeline
2. Collar
3. The tank is filled with hydraulic liquid
check liquid level in a tank (on marks
on the tank) after the engine will work during 2минут, wheels thus should stand directly
muffle the engine, check level of liquid and add to a mark the MOVE if it is necessary
4. Collar
5. A soaking-up hose
6. Filter
clean cleaning solution
7. Spring clamp
it is put on on щуп for measurement of level of liquid
8. Spring
9. Uplotnitelno ring
10. Cover of a jellied opening

Pump of system of hydrostrengthening of a steering

1. Laying plate *
it is inserted into laying
2. Прокладка*
3. A plate with openings
4. Lock ring *
5. 15 N of m.
grease with D6 hermetic before installation
longer end twists in the pump case
6. A pump shaft with a flange check on existence of scratches and wear tracks
if it is necessary, replace all pump
remove poтор and a shaft for
replacements of a sealing ring
7. Sealing кольцо*
for replacement, it is necessary to disassemble the pump
8. Case
oil channels (are specified by an arrow) both halves of the case should coincide after assembly
9. Sealing кольцо*
10. Rotor
11. Blades
the polished surface (it is specified by an arrow) should be turned outside
12. Stator
provision of installation: the arrow on a stator should be visible after installation
13. Valve clamp
akkumratno remove by means of small отверкти
14. The restrictive valve, do not assort
15. Spring
16. Case

The dual hydraulic pump for model with the 20-klapanny engine

1. A bolt for a tension of a maple belt
2. Clip
3. 20 N of m.
4. Rotary arm
5. 20 N of m.
6. З0Н.м.
during the untwisting or removal, always replace with a detail 100 067 04
7. Mobile arm
8. 20 N of m.
9. 20 N of m.
10. Maple belt, size: 12.5x992 mm
11. A pulley, establish a mark "5Z" forward
12. 10 N of m.
13. The pump with two pistons
systems of a servousileniye of brakes
14. Lopastna pump
before installation, fill soaking-up part with hydraulic liquid and повращайте the pump that liquid began to leave the target channel
15. The return pipeline, from a tee
16. The tube of a high pressure, goes to a steering lath
17. 50 N of m.
18. 20 N of m.
19. 35 N of m.
20. Tube of a high pressure