Audi 80/90/Coupe

since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburetors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
- 11. Steering
   11.2. Shaft and casing of a steering column
   11.3. A power absorbing steering column
   11.4. Steering drive
   11.5. Pipeline of high pressure / return pipeline
   11.6. Adjustment of a free wheeling of a lath of a steering
   11.7. Maple belt
   - 11.8. System of hydrostrengthening of a steering
      11.8.1. Technical characteristics
      11.8.2. Pumping / filling of hydraulic liquid
      11.8.3. Check on tightness (at the working engine)
      11.8.4. Steering transfer
      11.8.5. Pump of the hydraulic booster of a steering (Vickers)
+ 12. Body, salon
+ 13. Central air
+ 14. Electric equipment







dfe5d7b3


11.8.4. Steering transfer

GENERAL INFORMATION

Steering transfer with the hydraulic booster, models since 8А MA 054 850 (A sedan with 5-циллиндровым the engine) – 8А MA 002 645 (an all-wheel drive Compartment)

1. Lath case
2. Epiploon рейки*
3. Lock ring
it is possible to remove / establish only after lath removal
4. Fixing ring
put on a steering lath against the stop 
establish a cover on a flute passing on a circles of a ring
5. Cover
it is possible to replace, without removing the reechny steering mechanism
6. Collar
use a collar which is pulled together by means of the screw, the screw should be turned to a body
7. A sealing ring, always replace
8. Adjusting screw
9. 20 N of m.
10. Cover
11. Sealing ring
35x2.5
always replace
it is established in a flute on the case
12. Sealing ring
27x2.5 mm
always replace
it is established in a plug flute
13. Plug
14. Kompressionny spring
 it is established in the slider
15. Toddler
16. Washer

17. 20 N of m.
18. Casing of a leading gear wheel
19. Epiploon
 always replace
20. Washer
21. Штифт*
2.5x6 mm
always replace
pull out a pin by means of flat-nose pliers before removal of a casing of a leading gear wheel
22. Leading gear wheel / ring valve
23. Sealing ring
9x2 mm
24. Sealing ring
25. Cover
inhaling moment: 50 N of m.
tighten by means of two center punches established at an angle in 180 ° to each other
26. Fixing ring
always replace
27. Sealing ring
44x2.5 mm
always replace
28. Steering lath
for removal: turn off a cover and pull out a lath on the left side of the case
check a lath on existence of scratches round an epiploon installation site

All elements marked with an asterisk, are included in a repair kit and should be replaced during repair.

Prevention

The system of hydrostrengthening of a steering is filled with hydraulic liquid, G 002 000 detail.

Works with a drive of a steering should be carried out on a pure place and all elements should contain in absolute purity.


Steering transfer for Compartment model

1. Washer
2. 35 N of m.
3. 45 N of m, always replace
4. 45 N of m, always replace
5. Adjusting screw
6. 40 N of m, at removal, hold a head of the dempferny plug by means of a wrench
7. Arm
8. The plug with a carving, is a part of the dempferny mechanism of a steering
9. The Dempferny plug, remove before lath and arm removal