The device, service, Audi 80/90/Coupe 1986-1991 repair - 12.10. Back door (Compartment model)//Audi / songwizard.ru

Audi 80/90/Coupe

since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburetors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
   12.2. Central section of a guard
   12.3. Cowl rope
   12.4. Forward guard
   12.5. Forward wing
   12.6. Lock pins of a cowl, rubber shock-absorber
   12.7. Cowl
   12.8. Gas-filled rack (Sedan models)
   12.9. Trunk lid
   12.10. Back door (Compartment model)
   12.11. Forward door, bottom door loop
   12.12. Adjustment of a window and a bearing element of a door
   12.13. Window condensing jams, a window regulator
   12.14. Door lock
   12.15. Draft of lever transfer of the lock
   12.16. Rope of the internal door lock
   12.17. Rotary clamp, adjusting spring
   12.18. Adjustment of doors
   12.19. A bearing element of a door
   12.20. Central lock
   12.21. The pump with two modes of forcing
   12.22. Leading activator
   12.23. Activator of a back door
   12.24. Trunk lid activator
   12.25. Activator of a cover of a fuel tank
   12.26. Door glass (Compartment model)
   12.27. Adjustment of a butt slip (Compartment model)
   12.28. Framework of a back door, bottom loop of a door
   12.29. A bearing element of the back door, a condensing stopper
   12.30. Rope, sharnirny lever
   12.31. Door handle
   12.32. Holder of components of a door
   12.33. Hatch
   12.34. Bumper casing
   12.35. Sealing of a rear bumper
   12.36. An extending clamp
   12.37. Forward spoiler / laying of a niche of a wheel (Compartment model)
   12.38. Top overlay of a forward spoiler (Compartment model)
   12.39. Back spoiler / laying of a niche of a wheel
   12.40. Rear bumper (Compartment model)
   12.41. Window regulators
   12.42. Internal furnish of a body
   12.43. Sitting
+ 13. Central air
+ 14. Electric equipment


dfe5d7b3



12.10. Back door (Compartment model)

GENERAL INFORMATION

Back door in assembly (Compartment model)

1. Six-sided nut, 8 N of m.
2. Locking plate; has the contact switch of a lamp of a luggage carrier
3. A bolt with a flat head and a washer, 4 N of m.
4. Adjusting washer
5. Condensing laying
6. Lock washer
7. Hinge
8. Laying
9. Six-sided nut, 21 N of m.
10. Basis
11. Hinge axis
12. Washer
13. Bolt, 10 N of m.
14. Gas-filled rack
15. Clip, 10 N of m.
16. Bolt; onboard a body
17. Washer; onboard a body
18. Sealing ring; onboard a body
19. Clip; on a body boat

Back door, removal (Compartment model)

PERFORMANCE ORDER
1) remove a decorative covering from a frame of a back part of a roof
2) remove a decorative covering of a back door
3) disconnect a screen wiper of back glass
4) remove a plait of wires from a back door
5) extend a block cable connector of a screen wiper of back glass from a cavity
Prevention

For simplification of installation of the flexible pipeline of a washer, attach it to a back door a wire.


6) disconnect a jet of a washer and remove the pipeline

Back door, installation (Compartment model)

Installation carry out upside-down.

Back door, assembly

1. Condensing laying of a groove of a window
removal is possible only at the bracket removed from a door
2. 8 N of m.
3. Condensing laying
it is fixed by means of universal KD5 05 AKD 476 glue
4. Door covering
5. An extending clamp
6. Shock-proof fittings
7. 8 N of m.
8. The bottom loop of the lock with the limiter of opening of a door
9. Top loop of a door
10. 30 N of m.
11. Overlay of a groove of a door
only on the Audi-90 models
for removal pull out from the top part of an upholstery of a door
installation: clear a groove by means of a cleaner
place in a groove pressurizing substance in thickness of 3.0 mm
establish a slip on a covering of a door and press on it for installation in the relevant situation

Lateral part of a body

Arrangement of elements


PERFORMANCE ORDER
1) press on 1 against the stop
2) tighten the screw 2 with internal shestigranniky 0.4 N of m.
3) close the hatch for installation of all components in initial situation
4) tighten the screw with internal shestigranniky 6 N of m.

Back door, adjustment

Arrangement of elements


PERFORMANCE ORDER
1) adjust a locking plate 1 to and = 12.0±1.0 mm
2) tighten 2 with the moment of 0.4 N of m.
3) close a back door for installation of all components in initial situation
4) open a back door and tighten 2 with the moment of 6 N of m.

Lock of a back door, assembly (Compartment model)

1. Locking plate
contains the contact switch of a lamp of a luggage carrier
adjustment: place a locking plate in the center and tighten with the moment of 0.8 N of m.
close a luggage carrier for a centering and alignment of a locking plate
slightly slightly open and tighten six-sided nuts of a shock plate
2. Six-sided nut, 8 N of m.
3. Draft of lever transfer
do not establish with a tension; maximum free wheeling of 2.0 mm
4. Transitional plug
5. Plug
6. Laying
7. Plug
displace it for fixing of draft of lever transfer
8. Six-sided nut, 4 N of m.
9. Lock cylinder
10. Lock
11. Six-sided nut, 8 N of m.