The device, service, Audi 80/90/Coupe 1986-1991 repair - 12.12. Adjustment of a window and a bearing element of a door//Audi / songwizard.ru

Audi 80/90/Coupe

since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburetors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
   12.2. Central section of a guard
   12.3. Cowl rope
   12.4. Forward guard
   12.5. Forward wing
   12.6. Lock pins of a cowl, rubber shock-absorber
   12.7. Cowl
   12.8. Gas-filled rack (Sedan models)
   12.9. Trunk lid
   12.10. Back door (Compartment model)
   12.11. Forward door, bottom door loop
   12.12. Adjustment of a window and a bearing element of a door
   12.13. Window condensing jams, a window regulator
   12.14. Door lock
   12.15. Draft of lever transfer of the lock
   12.16. Rope of the internal door lock
   12.17. Rotary clamp, adjusting spring
   12.18. Adjustment of doors
   12.19. A bearing element of a door
   12.20. Central lock
   12.21. The pump with two modes of forcing
   12.22. Leading activator
   12.23. Activator of a back door
   12.24. Trunk lid activator
   12.25. Activator of a cover of a fuel tank
   12.26. Door glass (Compartment model)
   12.27. Adjustment of a butt slip (Compartment model)
   12.28. Framework of a back door, bottom loop of a door
   12.29. A bearing element of the back door, a condensing stopper
   12.30. Rope, sharnirny lever
   12.31. Door handle
   12.32. Holder of components of a door
   12.33. Hatch
   12.34. Bumper casing
   12.35. Sealing of a rear bumper
   12.36. An extending clamp
   12.37. Forward spoiler / laying of a niche of a wheel (Compartment model)
   12.38. Top overlay of a forward spoiler (Compartment model)
   12.39. Back spoiler / laying of a niche of a wheel
   12.40. Rear bumper (Compartment model)
   12.41. Window regulators
   12.42. Internal furnish of a body
   12.43. Sitting
+ 13. Central air
+ 14. Electric equipment


dfe5d7b3



12.12. Adjustment of a window and a bearing element of a door

Bearing element of making elements of a door

Removal

PERFORMANCE ORDER
1) remove the decorative panel of a forward door
2) remove a rope from the internal mechanism of opening of a door

Installation and adjustment

Installation carry out upside-down, in view of the following:

PERFORMANCE ORDER
1) check adjustment of an upholstery of a door
2) adjust a support of a bearing element of a door
3) tighten bolts with a six-sided head (arrow) of 20 N of m.
4) section A-and

adjust the window limiter on the window lift

reduce together area B and an internal sealant of a window

5) during adjustment the door flew down should be closed

adjust the top limiter of a regulator of a window so that the edge of internal sealing laying in area B adjoined to the upper edge of a window

and = 0.5 mm


Prevention

If previously to load a sealant so that it was compressed at least on 0.5 mm, it will allow to avoid course.