Audi 80/90/Coupe + 1.2. Car identification + 2. Engines, carburetors
3. Greasing system + 4. Cooling system + 5. Fuel system + 6. Exhaust system + 7. Ignition system + 8. Transmission + 9. Suspension brackets, wheels + 10. Brake system + 11. Steering - 12. Body, salon 12.2. Central section of a guard 12.3. Cowl rope 12.4. Forward guard 12.5. Forward wing 12.6. Lock pins of a cowl, rubber shock-absorber 12.7. Cowl 12.8. Gas-filled rack (Sedan models) 12.9. Trunk lid 12.10. Back door (Compartment model) 12.11. Forward door, bottom door loop 12.12. Adjustment of a window and a bearing element of a door 12.13. Window condensing jams, a window regulator 12.14. Door lock 12.15. Draft of lever transfer of the lock 12.16. Rope of the internal door lock 12.17. Rotary clamp, adjusting spring 12.18. Adjustment of doors 12.19. A bearing element of a door 12.20. Central lock 12.21. The pump with two modes of forcing 12.22. Leading activator 12.23. Activator of a back door 12.24. Trunk lid activator 12.25. Activator of a cover of a fuel tank 12.26. Door glass (Compartment model) 12.27. Adjustment of a butt slip (Compartment model) 12.28. Framework of a back door, bottom loop of a door 12.29. A bearing element of the back door, a condensing stopper 12.30. Rope, sharnirny lever 12.31. Door handle 12.32. Holder of components of a door 12.33. Hatch 12.34. Bumper casing 12.35. Sealing of a rear bumper 12.36. An extending clamp 12.37. Forward spoiler / laying of a niche of a wheel (Compartment model) 12.38. Top overlay of a forward spoiler (Compartment model) 12.39. Back spoiler / laying of a niche of a wheel 12.40. Rear bumper (Compartment model) 12.41. Window regulators 12.42. Internal furnish of a body 12.43. Sitting + 13. Central air + 14. Electric equipment
|
The door lock, draft of the lock in the lock assembly / cylinder in assembly
1. Lock control lever 2. Draft of lever transfer of the lock at removal disconnect the lock 3. Control lever clip 4. Plastic washer 5. 16 N of m. 6. Konusny washer two konusny washers if it is necessary for adjustment can be established 7. Bolt of a locking plate of the door lock, 50 N of m. 8. Door lock 9. A rope, for work in a door |
10. Clips, watch the direction of the main draft in a clip 11. Condensing laying 12. Fixing plate of draft of the lock 13. Rotary clamp for removal зажиа to turn on 65 ° 14. 3 N of m. 15. Door handle 16. External plate of the lock 17. Draft of lever transfer of the lock, lock cylinder pay attention that draft is attached by means of the sharnirny plug |
Door lock
1. A bolt with a cylindrical head, 3 N of m. 2. Door handle 3. Lock cylinder remove only by means of a key 4. A condensing ring 5. Plate |
6. Spring 7. A control lever with the loose leaf 8. The with-shaped 9. Lock clamp for removal to turn on 65 ° |
Door lock
Removal
PERFORMANCE ORDER |
1) remove the decorative panel of a forward door |
2) disconnect a clip of draft of lever transfer and extend draft |
3) disconnect a rope |
4) pull out the door lock from a hub 2 |
5) remove laying 3 |
|
Installation
Installation carry out upside-down, in view of the following:
PERFORMANCE ORDER |
1) again to connect a rope, pull the lever 4 in the arrow direction; insert a screw-driver into an opening 5 to establish a rope into place |
2) screw up all bolts with the moment of 16 N of m. |
|
The door lock in assembly (Compartment model)
1. External plate of the door lock 2. Door handle 3. Washer 4. A bolt with a head under a face key 5. Draft of the lock – the lock cylinder at removal displace the rotary plug 6. Rope 7. Clips watch the direction of the main draft in a clip 8. Draft of the lock 9. Door lock 10. A screw with a crosswise head 11. Fixing plate of draft of the lock |
12. Bolt, 16 N of m. 13. Clamp 14. Clamp substrate more than one can be established 15. Condensing laying 16. Door lock 17. The self-cutting screw with a ploskokonichesky head, 16 N of m. 18. A clamp for a control lever press on the coupling to remove draft of lever transfer of the lock 19. Draft of the lock 20. Draft of a control lever of the lock 21. Button of the door lock 22. Rotary clamp |
Door lock (Compartment model)
Removal
PERFORMANCE ORDER |
1) remove the decorative panel of a forward door |
2) disconnect a clip of draft of lever transfer and extend draft |
3) disconnect a rope |
4) pull out the door lock from a hub 2 |
|
Installation
Installation carry out upside-down, in view of the following:
PERFORMANCE ORDER |
1) connect a rope, having pulled the lever 4 in the direction specified by an arrow |
2) place a screw-driver in an opening 5 to establish a rope into place |
3) screw up all bolts with the moment of 16 N of m. |
|
Cover of the door lock, removal
PERFORMANCE ORDER |
|
disconnect a cover from a door covering |
|
Cover of the door lock, installation
Installation carry out upside-down. Decorative covering of the handle of the lock, removal
Prevention
The decorative covering of the handle of a door should be removed before removal of the handle not to allow damage of the painted surface of a decorative covering.
PERFORMANCE ORDER |
1) lift the door handle |
|
2) pull out the lock probe in the direction specified by an arrow |
3) remove a decorative covering |
|
The door lock (Compartment models since 1990 modeling years)
1. Adjusting detail squeezing the lever on a carving and it can be adjusted through a fixing opening 2. Lock opening 3. Door lock 4. 16 N of m. 5. Plastic washer 6. Konusny washer two konusny washers can be in case of need established 7. Pin of a latch of 50 N of m. 8. A rope for the internal lock of a door |
9. Clamp pay attention to the provision of a rope in clamps 10. Clamp for a detachment of a clamp remove a rope and turn a clamp on 90 ° 11. An extending clamp 12. Sharnirny lever 13. Draft of the lever mechanism 14. Condensing laying 15. Rope of the lock of a door 16. Door handle 17. External covering of the handle of a door 18. 3 N of m. |
The door lock (Compartment models since 1990 modeling years)
Removal
PERFORMANCE ORDER |
1) remove the decorative panel of a forward door |
2) turn the lever 1, having pulled a rope in the direction specified by an arrow, and supporting in the necessary situation by means of a screw-driver through an opening 2 |
3) disconnect a rope |
4) unscrew bolts |
5) pull out the door lock from a clamp 3, sealants 5 |
|
Installation
Installation carry out upside-down, in view of the following:
PERFORMANCE ORDER |
1) attach a rope |
2) insert the door lock into a clamp |
3) combine the door handle with the lock |
4) adjust, as it is required |
5) send the driving mechanism 4 to the driving lever of the lock of a door; this operation can be observed through an opening for access |
|
|
|