The device, service, Audi 80/90/Coupe 1986-1991 repair - 12.19. A bearing element of a door//Audi / songwizard.ru

Audi 80/90/Coupe

since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburetors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
   12.2. Central section of a guard
   12.3. Cowl rope
   12.4. Forward guard
   12.5. Forward wing
   12.6. Lock pins of a cowl, rubber shock-absorber
   12.7. Cowl
   12.8. Gas-filled rack (Sedan models)
   12.9. Trunk lid
   12.10. Back door (Compartment model)
   12.11. Forward door, bottom door loop
   12.12. Adjustment of a window and a bearing element of a door
   12.13. Window condensing jams, a window regulator
   12.14. Door lock
   12.15. Draft of lever transfer of the lock
   12.16. Rope of the internal door lock
   12.17. Rotary clamp, adjusting spring
   12.18. Adjustment of doors
   12.19. A bearing element of a door
   12.20. Central lock
   12.21. The pump with two modes of forcing
   12.22. Leading activator
   12.23. Activator of a back door
   12.24. Trunk lid activator
   12.25. Activator of a cover of a fuel tank
   12.26. Door glass (Compartment model)
   12.27. Adjustment of a butt slip (Compartment model)
   12.28. Framework of a back door, bottom loop of a door
   12.29. A bearing element of the back door, a condensing stopper
   12.30. Rope, sharnirny lever
   12.31. Door handle
   12.32. Holder of components of a door
   12.33. Hatch
   12.34. Bumper casing
   12.35. Sealing of a rear bumper
   12.36. An extending clamp
   12.37. Forward spoiler / laying of a niche of a wheel (Compartment model)
   12.38. Top overlay of a forward spoiler (Compartment model)
   12.39. Back spoiler / laying of a niche of a wheel
   12.40. Rear bumper (Compartment model)
   12.41. Window regulators
   12.42. Internal furnish of a body
   12.43. Sitting
+ 13. Central air
+ 14. Electric equipment


dfe5d7b3



12.19. A bearing element of a door

GENERAL INFORMATION

Bearing element of a door, the sizes

in drawing the cross-section section of the left door is shown

the sealing edge 7 should have contact on all contour of a rack and a decorative overlay of a roof 3

with = 3.5 + 1 mm

d= 8.1 + 1 mm

1–sealing flange
2–door frame
3–decorative overlay of a door
4–window
5–window sealing laying
6–internal door sealing laying
7–sealing edge
8–a sealing edge at a window

Adjustment

Prevention

The first windows and a door covering should be adjusted.

Two experts will be necessary for implementation of this operation. Do not press a door covering during adjustment.


PERFORMANCE ORDER
1) weaken bolts (shooters)
2) close a door
3) slightly press on bearing element in the direction opposite to a roof and a rack; apply slightly more force, than it is necessary; rubber laying will return bearing element to appropriate situation
4) at this time the second expert (from within the car) tightens at first top, and then the bottom bolts

Bearing element of a back door, removal / installation


 

Removal

PERFORMANCE ORDER
1) remove the decorative panel of a door
2) disconnect a rope of the internal uncoupling mechanism of a door
3) disconnect and remove a rope from a bearing element of a door
4) remove a fixing pin 1, having pressed forward on a covering of the lock of a door
5) unscrew bolts with a six-sided head 2, 3

Installation

Installation carry out upside-down, in view of the following:

tighten bolts with a six-sided head with the moment of 20 N of m.

A-and – a cross-section

In = a zone between a roof and a back rack of a body

1–adjustable limiter of a regulator of a window

adjust the top limiter of a regulator of a window so that the upper edge of a window 3 adjoined to condensing flange 2 in a transitional zone B

and = 0 + 0.5 mm