Audi 80/90/Coupe

since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburetors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
   12.2. Central section of a guard
   12.3. Cowl rope
   12.4. Forward guard
   12.5. Forward wing
   12.6. Lock pins of a cowl, rubber shock-absorber
   12.7. Cowl
   12.8. Gas-filled rack (Sedan models)
   12.9. Trunk lid
   12.10. Back door (Compartment model)
   12.11. Forward door, bottom door loop
   12.12. Adjustment of a window and a bearing element of a door
   12.13. Window condensing jams, a window regulator
   12.14. Door lock
   12.15. Draft of lever transfer of the lock
   12.16. Rope of the internal door lock
   12.17. Rotary clamp, adjusting spring
   12.18. Adjustment of doors
   12.19. A bearing element of a door
   12.20. Central lock
   12.21. The pump with two modes of forcing
   12.22. Leading activator
   12.23. Activator of a back door
   12.24. Trunk lid activator
   12.25. Activator of a cover of a fuel tank
   12.26. Door glass (Compartment model)
   12.27. Adjustment of a butt slip (Compartment model)
   12.28. Framework of a back door, bottom loop of a door
   12.29. A bearing element of the back door, a condensing stopper
   12.30. Rope, sharnirny lever
   12.31. Door handle
   12.32. Holder of components of a door
   12.33. Hatch
   12.34. Bumper casing
   12.35. Sealing of a rear bumper
   12.36. An extending clamp
   12.37. Forward spoiler / laying of a niche of a wheel (Compartment model)
   12.38. Top overlay of a forward spoiler (Compartment model)
   12.39. Back spoiler / laying of a niche of a wheel
   12.40. Rear bumper (Compartment model)
   12.41. Window regulators
   12.42. Internal furnish of a body
   12.43. Sitting
+ 13. Central air
+ 14. Electric equipment


dfe5d7b3



12.2. Central section of a guard

Removal
PERFORMANCE ORDER
1) remove a bumper
2) remove a front grille
3) remove the decorative panel
4) pull out a guard from condensing rings

Installation

Installation carry out upside-down:
PERFORMANCE ORDER
1) unscrew an air line of cooling air and fastening from a radiator above
2) remove the central section of a guard

Forward guard, removal

PERFORMANCE ORDER
1) remove a bumper
2) remove a front grille
3) unscrew the decorative panel (arrows)
4) pull out a guard from a condensing ring to the right or to the left

Forward guard, Sedan


1. A bolt with a six-sided head, 23 N of m.
2. The self-cutting screw, 7.5 N of m.
3. Guard, bottom section
it is possible to remove together with the central section
4. The self-cutting screw, 7.5 N of m.
5. A bolt with a six-sided head, 23 N of m.
6. A bearing plate of the lock, it is possible to remove together with the central or bottom section
7. A metal ear, at removal of a guard pull it directly down for a corner
8. The self-cutting screw, 7.5 N of m.
9. Guard, central section

Forward guard, removal for the Sedan model

PERFORMANCE ORDER
1) through an opening for access remove the holder of a rope and disconnect a rope
2) unscrew screws of a casing of stitched air (arrow)
3) to remove a guard, pull it down under a wing

Forward guard, installation

Installation carry out upside-down.

Forward wing, removal
PERFORMANCE ORDER
1) remove a front bumper
2) remove laying of a cavity of a wheel
3) remove condensing laying (shooter)

Forward wing, removal. Adjustment of a forward wing, cowl gap
PERFORMANCE ORDER
unscrew fixing bolts and self-cutting screws

Forward wing, installation

Installation carry out upside-down. Pay attention to the following:

PERFORMANCE ORDER
1) establish a rivet for a basic arm of a cowl (arrow A)
2) establish a rivet for a stopper doors (arrow B)
3) establish strips of a sealing cord, 1, 2 and sheet laying with a bolt And on a stopper

1= 480 mm at length and 7.0 mm in diameter

2= 250 mm at length and 7.0 mm in diameter


Prevention

The sealing cord will be necessary for compressing till the diameter in 7.0 mm


Adjustment of a forward wing, cowl gap

PERFORMANCE ORDER
1) weaken all bolts of a wing
2) having weakened bolts, adjust a gap, moving a wing

and = 4.5 + 1.0 mm

Forward guard assembled for Compartment models

1. A bolt with a six-sided head, 23 N of m.
2. The self-cutting screw with a washer
3. Guard, central section
4. Guard, bottom section
5. The self-cutting screw with a washer

Forward guard, removal for Compartment model

PERFORMANCE ORDER
1) remove a bumper
2) remove a front grille
3) disconnect a cowl rope
4) unscrew screws of a decorative covering (arrow) and pull out it from a condensing ring
5) unscrew an air line of cooling air and an arm of a radiator (arrow)
6) unscrew an arm of an oil radiator
7) disconnect the switch of a lamp of motor office
8) disconnect a connecting loop on the guard panel
9) unscrew directing device of soaked-up air (arrow)

Cowl rope, detachment for the Sedan model

PERFORMANCE ORDER
1) through an opening for access remove the holder of a rope and disconnect a rope
2) unscrew screws of a casing of stitched air (arrow)
3) through an opening for access disconnect the holder of a rope 1
4) disconnect a rope from an arm 2

Forward guard, installation. The central section of a guard, removal / installation for Compartment model

PERFORMANCE ORDER
to remove a guard, pull it down under a wing (shooter)

Forward guard, installation

Installation carry out upside-down.

Central section of a guard, removal

PERFORMANCE ORDER
1) remove a bumper
2) remove a front grille
3) disconnect a cowl rope
4) unscrew screws of a decorative covering (arrow) and pull out it from a condensing ring
5) unscrew an air line of cooling air and an arm of a radiator (arrow)
6) unscrew and remove the central section of a guard

Central section of a guard, installation

Installation carry out upside-down.