Audi 80/90/Coupe + 1.2. Car identification + 2. Engines, carburetors
3. Greasing system + 4. Cooling system + 5. Fuel system + 6. Exhaust system + 7. Ignition system + 8. Transmission + 9. Suspension brackets, wheels + 10. Brake system + 11. Steering - 12. Body, salon 12.2. Central section of a guard 12.3. Cowl rope 12.4. Forward guard 12.5. Forward wing 12.6. Lock pins of a cowl, rubber shock-absorber 12.7. Cowl 12.8. Gas-filled rack (Sedan models) 12.9. Trunk lid 12.10. Back door (Compartment model) 12.11. Forward door, bottom door loop 12.12. Adjustment of a window and a bearing element of a door 12.13. Window condensing jams, a window regulator 12.14. Door lock 12.15. Draft of lever transfer of the lock 12.16. Rope of the internal door lock 12.17. Rotary clamp, adjusting spring 12.18. Adjustment of doors 12.19. A bearing element of a door 12.20. Central lock 12.21. The pump with two modes of forcing 12.22. Leading activator 12.23. Activator of a back door 12.24. Trunk lid activator 12.25. Activator of a cover of a fuel tank 12.26. Door glass (Compartment model) 12.27. Adjustment of a butt slip (Compartment model) 12.28. Framework of a back door, bottom loop of a door 12.29. A bearing element of the back door, a condensing stopper 12.30. Rope, sharnirny lever 12.31. Door handle 12.32. Holder of components of a door 12.33. Hatch 12.34. Bumper casing 12.35. Sealing of a rear bumper 12.36. An extending clamp 12.37. Forward spoiler / laying of a niche of a wheel (Compartment model) 12.38. Top overlay of a forward spoiler (Compartment model) 12.39. Back spoiler / laying of a niche of a wheel 12.40. Rear bumper (Compartment model) 12.41. Window regulators 12.42. Internal furnish of a body 12.43. Sitting + 13. Central air + 14. Electric equipment
|
Front bumper, assembly
1. 30 N of m. 2. 23 N of m. 3. Absorber of shock loading 4. Bumper crossbeam for removal it is necessary to remove a bumper casing 5. The central decorative strip removal: pull out from under fixing pads (the bumper should be disassembled, and the crossbeam is removed) 6. Broad nut 7. Towing hook 8. The marked openings | 9. Holder of registration plate 10. Bolts М5x12 11. Decorative facing (5 cylinders) 12. Decorative facing (4 cylinders) 13. Bumper casing 14. An extending clamp 15. Plastic nut 16. Rubber washer 17. Decorative strip 18. Cover 19. Arm 20. 30 N of m. 21. Directing |
Bumper casing, removal
PERFORMANCE ORDER |
1) remove extending fixing agents (insert) |
2) disconnect from directing and press on the ends in the direction down (arrow A) |
3) remove a cover from a decorative strip and unscrew bolts |
4) disconnect fixing pads from a bumper crossbeam |
5) decorative facing remove in the direction specified by an arrow B |
|
Towing hook, installation
|
1. Rivet
2. Prekladina
3. Kronsheyn of the towing hatch
|
Arm, installation
|
1. Crossbeam
2. Rivet
3. Arm
|
On all-wheel drive models the left absorber of shock loading fastens to a cross-piece an additional bolt. Tighten this bolt till 23 N of m.
Front bumper, assembly (Compartment model)
1. A bolt with a six-sided head, 23 N of m. 2. Washer 3. Blow absorber removal: remove a bumper unscrew bolts with a six-sided head 4. Washer three washers on each absorber 5. Bolts with a six-sided head, 23 N of m. 6. Washer 7. A bolt with a ploskokonichesky head, 23 N of m. 8. Spoiler removal: remove a bumper remove extending clamps unscrew a spoiler from a wheel niche unscrew the top fixing bolts on a spoiler disconnect washers of forward headlights if they are established remove a spoiler, having pulled out it directly from a body 9. Fog light if it is established, there is need no it to remove during spoiler removal 10. Bumper crossbeam for removal it is necessary to remove first of all a casing of a bumper and a decorative covering
|
11. Decorative strip 12. Bumper casing it is possible to remove after the bumper will be disconnected 13. Bolt / washer of 6 N of m. 14. Arm in an installation time it is necessary to establish a spoiler on an arm 15. Bolt / washer of 6 N of m. 16. Washer 17. Screw of 1,0 N of m. 18. The being self-cut screw with a ploskokonichesky head 19. Holder of registration plate 20. Nut 21. Washer remove a bumper from within unscrew bolts with a six-sided head in front remove a washer jet 22. Six-sided nut the jet of a washer of a headlight fixes |
|
|