Audi 80/90/Coupe + 1.2. Car identification + 2. Engines, carburetors
3. Greasing system + 4. Cooling system + 5. Fuel system + 6. Exhaust system + 7. Ignition system + 8. Transmission + 9. Suspension brackets, wheels + 10. Brake system + 11. Steering - 12. Body, salon 12.2. Central section of a guard 12.3. Cowl rope 12.4. Forward guard 12.5. Forward wing 12.6. Lock pins of a cowl, rubber shock-absorber 12.7. Cowl 12.8. Gas-filled rack (Sedan models) 12.9. Trunk lid 12.10. Back door (Compartment model) 12.11. Forward door, bottom door loop 12.12. Adjustment of a window and a bearing element of a door 12.13. Window condensing jams, a window regulator 12.14. Door lock 12.15. Draft of lever transfer of the lock 12.16. Rope of the internal door lock 12.17. Rotary clamp, adjusting spring 12.18. Adjustment of doors 12.19. A bearing element of a door 12.20. Central lock 12.21. The pump with two modes of forcing 12.22. Leading activator 12.23. Activator of a back door 12.24. Trunk lid activator 12.25. Activator of a cover of a fuel tank 12.26. Door glass (Compartment model) 12.27. Adjustment of a butt slip (Compartment model) 12.28. Framework of a back door, bottom loop of a door 12.29. A bearing element of the back door, a condensing stopper 12.30. Rope, sharnirny lever 12.31. Door handle 12.32. Holder of components of a door 12.33. Hatch 12.34. Bumper casing 12.35. Sealing of a rear bumper 12.36. An extending clamp 12.37. Forward spoiler / laying of a niche of a wheel (Compartment model) 12.38. Top overlay of a forward spoiler (Compartment model) 12.39. Back spoiler / laying of a niche of a wheel 12.40. Rear bumper (Compartment model) 12.41. Window regulators 12.42. Internal furnish of a body 12.43. Sitting + 13. Central air + 14. Electric equipment
|
Forward wing, assembly (Compartment model)
1. Nut 2. A self-cutting bolt with a washer, 8 N of m. 3. A self-cutting bolt with a washer 4. Wing 5. An extending nut |
6. Wing arm 7. A self-cutting bolt with a washer, 8 N of m. 8. Washer 9. A condensing ring 10. Condensing laying |
Forward wing, removal
PERFORMANCE ORDER |
1) remove a front bumper |
2) remove laying of a cavity of a wheel |
|
3) remove condensing laying (shooter) |
|
Installation
All components establish in the return to removal an order, in view of the following:
PERFORMANCE ORDER |
|
1) establish a rivet of a basic arm of a cowl (arrow A) |
2) establish a stopper rivet doors (arrow B) |
|
3) establish strips of a sealing cord, 1, 2 and sheet laying with a bolt And on a stopper
1= 480 mm at length and 7.0 mm in diameter
2= 250 mm at length and 7.0 mm in diameter
|
|
Use a sealing cord of AKD 497 010 04 R10 or an equivalent, and compress it till the sizes of 7.0 mm in diameter.
Adjustment of a forward wing, cowl gap
PERFORMANCE ORDER |
1) weaken all bolts of a wing |
2) having weakened bolts, adjust a gap, moving a wing |
|
3) having weakened bolts, adjust a gap, moving a wing
and = 4.5 + 1.0 mm |
|
Prevention
Numbers of details are intended only for the reference. For the most last information always address to your dealer.
The sealing cord will be necessary for compressing till the diameter in 7.0 mm
|
|