Audi 80/90/Coupe

since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburetors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
   12.2. Central section of a guard
   12.3. Cowl rope
   12.4. Forward guard
   12.5. Forward wing
   12.6. Lock pins of a cowl, rubber shock-absorber
   12.7. Cowl
   12.8. Gas-filled rack (Sedan models)
   12.9. Trunk lid
   12.10. Back door (Compartment model)
   12.11. Forward door, bottom door loop
   12.12. Adjustment of a window and a bearing element of a door
   12.13. Window condensing jams, a window regulator
   12.14. Door lock
   12.15. Draft of lever transfer of the lock
   12.16. Rope of the internal door lock
   12.17. Rotary clamp, adjusting spring
   12.18. Adjustment of doors
   12.19. A bearing element of a door
   12.20. Central lock
   12.21. The pump with two modes of forcing
   12.22. Leading activator
   12.23. Activator of a back door
   12.24. Trunk lid activator
   12.25. Activator of a cover of a fuel tank
   12.26. Door glass (Compartment model)
   12.27. Adjustment of a butt slip (Compartment model)
   12.28. Framework of a back door, bottom loop of a door
   12.29. A bearing element of the back door, a condensing stopper
   12.30. Rope, sharnirny lever
   12.31. Door handle
   12.32. Holder of components of a door
   12.33. Hatch
   12.34. Bumper casing
   12.35. Sealing of a rear bumper
   12.36. An extending clamp
   12.37. Forward spoiler / laying of a niche of a wheel (Compartment model)
   12.38. Top overlay of a forward spoiler (Compartment model)
   12.39. Back spoiler / laying of a niche of a wheel
   12.40. Rear bumper (Compartment model)
   12.41. Window regulators
   12.42. Internal furnish of a body
   12.43. Sitting
+ 13. Central air
+ 14. Electric equipment


dfe5d7b3



12.9. Trunk lid

GENERAL INFORMATION

Trunk lid, hinge, rack (Sedan models)

1. Trunk lid limiter
2. The Sharnirny limiter, in the closed position
3. Insulating washer
4. Combinational bolt, 21 N of m.
5. A fixing clip
6. Gas-filled rack
7. Six-sided nut, 21 N of m.

Trunk lid, adjusting gap

Placement of the sizes


Size
Adjustment
and = 4.4 + 1.0 mm
Regulate the hinge
b= 6.5 + 1.0 mm
Adjustment it is carried out at change of the triangular panel
with = 9.9 + 1.0 mm
It is regulated by shift of stoplights
d= 8.0 + 1.0 mm
е= 9.75 + 1.0 mm
Adjustment is made on a locking plate of a trunk lid

The locking mechanism of a trunk lid in assembly (Sedan model)


1. A sealing ring for the lock cylinder
2. Draft of lever transfer
adjustment: place the lock and the lock cylinder so that in draft of rachazhny transfer there was no free wheeling; fix draft of lever transfer on the lock and fix
3. The jointed plug
4. Spring washer
5. A bolt with a six-sided head
6 N of m.
6. Spring pin
7. Clown
remove carefully not to lose a spring ball
8. A bolt with a six-sided head
3 N of m.
9. Washer
10. Locking plate of the door lock
11. A sealant, tear off a lining and paste on a shock plate of the door lock
12. Lock-nut, 3 N of m.
13. Lock
14. A sealant, tear off a lining and paste on the lock
15. Lock cylinder
for removal pull out a spring pin, remove the clown and by means of a key squeeze out the lock cylinder
16. Sealing ring
17. Lock
18. Spring
19. A spring ball, cover it with greasing before installation in the lock cylinder