Audi 80/90/Coupe

since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
- 1.2. Car identification
   1. Maintenance instruction
   1.3. Arrangement of identification plates
   1.4. Dashboard
   + 1.5. Car service
   - 1.6. Independent service of the car
      1.6.2. Small-sized spare wheel
      1.6.3. Wheel replacement
      + 1.6.4. Safety locks
      + 1.6.5. Replacement of bulbs
      1.6.6. Car audio replacement
      1.6.7. Car lifting
      1.6.8. General rules of towage
   + 1.7. Specifications
   1.8. Capacities
   1.9. Sizes
   1.10. Loadings
   1.11. Schedule preventive car servicings / greasings
+ 2. Engines, carburetors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
+ 12. Body, salon
+ 13. Central air
+ 14. Electric equipment


dfe5d7b3



1.6. Independent service of the car

1.6.1. Jack and tools

GENERAL INFORMATION

The jack and tool kit fasten by means of a bolt to fastening on the left side of a luggage carrier.

Before cleaning a jack in a luggage carrier, its handle should be lowered up to the end down.
The face wrench, screw-driver, key of 10 x 13 mm, ear for towage and a plastic pin for replacement of wheels fasten to a jack by means of a rubber strip.


Prevention

On the Audi-Kupe and Quattro models the jack and a tool kit fasten in a luggage carrier by means of a nut lamb. Always check, that these tools were reliably fixed and did not dangle, differently they can put a trauma to passengers in salon.

Use a jack only for wheel replacement. Never use a jack for lifting of other cars or other cargoes as it can lead to accident and traumas.

Never use a jack as a support at work under the car. If the jack casually to be displaced, you can get a serious trauma.

Do not lift the car, having established a jack under a bumper as in this case, you can seriously damage it. Also, the jack can jump out that will lead to receiving a corporal trauma.

Do not establish the car on shlakobetonny blocks, bricks or other props which can crumble under big weight.

Do not start the engine when the car costs on a jack.

At work under the car, always use the reliable support made specially for this purpose.


Face wrench

The face wrench is the tool serving for two purposes. The six-sided nest on the short end of a key approaches under bolts of fastening of wheels. The six-sided nest on the long end of a key approaches to spark plugs.

For convenience of removal and an inhaling of spark plugs, insert the screw-driver handle into a six-sided opening on the short end of a key.

The six-sided nest in the handle of a screw-driver is provided specially for simplification of removal and installation of bolts of fastening of wheels. Not to get injury, always clean a demountable edge when using the handle of a screw-driver for this purpose.


Prevention

The handle of a screw-driver should not be used for untwisting or an inhaling of bolts of fastening of wheels.


The plastic pin is used for simplification of replacement of wheels. When you insert a pin into an opening for a bolt, it guarantees that openings in a wheel will coincide with carving openings in a wheel nave.

Ear for car towage

For the car towage, entering into a tool kit, it is possible to twirl an ear in the anchor nest attached to a forward bamperny beam.

After installation, it is possible to stretch a towing cable through a towing ear.

At towage, observe towage rules.

Twirl a towing ear in an anchor nest and tighten a hand.

Remove a towing ear when it is not necessary for you any more.