The device, service, Audi 80/90/Coupe 1986-1991 repair - 7.1.10. Specifications (20-klapanny models)//Audi / songwizard.ru

Audi 80/90/Coupe

since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburetors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
- 7. Ignition system
   7.1.2. Specifications (4-cylinder models)
   7.1.3. Components of system of ignition for 5-cylinder models
   7.1.4. Specifications (5-cylinder models)
   7.1.5. CIS-E Motronic control unit (the alarm block)
   7.1.6. Distributor rotor
   7.1.7. Ignition distributor (4-cylinder models)
   7.1.8. Ignition distributor (5-cylinder models)
   7.1.9. Components of system of ignition for 20-klapanny models
   7.1.10. Specifications (20-klapanny models)
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
+ 12. Body, salon
+ 13. Central air
+ 14. Electric equipment


dfe5d7b3



7.1.10. Specifications (20-klapanny models)

GENERAL INFORMATION

Prevention

It is impossible to adjust a corner of an advancing of ignition. The corner of an advancing of ignition is defined by the electronic control unit.


Engine code
Ignition distributor
034 905 205 J
Main installation of the distributor of ignition
top dead point
Resistance of the sensor of the moment of ignition of fuel
about 1000 Ohm
Resistance of the sensor of number of turns of the engine
about 1000 Ohm
Spark plugs:
number
191 905 450 J
interelectrode gap
0.8 + 0.1 mm
inhaling moment
20 N of m.
Operating procedure of cylinders
1–2–4–5–3
Restriction of number of rpm. (fuel otsechka)
begins at 7200 rpm, comes to an end at 7400 rpm
Ignition coil:
secondary resistance
6500-8000 Ohm
primary resistance
about 0-1 Ohm
Resistance of a rotor of the distributor of ignition
1000 Ohm

Arrangement of an adjusting label

Specifications (20-klapanny models of 1990-1992 of release)

Ignition distributor
034 905 205 J
Ignition moment
top dead point
Resistance of the sensor of the moment of ignition of fuel
about 1000 Ohm
Resistance of the sensor of number of turns of the engine
about 1000 Ohm
Spark plugs:
type
Bosch F 6 DTC
number
101 000 004 АА
interelectrode gap
0.8 + 0.1 mm
inhaling moment
20 N of m.
Operating procedure of cylinders
1–2–4–5–3
Restriction of number of rpm. engine
begins at 7200 ± 200 rpm
Resistance check:
ignition coil
secondary resistance
6500-8000 Ohm
primary resistance
about 0-1 Ohm
rotor of the distributor of ignition
1000 Ohm

Prevention

The corner of an advancing of ignition is defined by the electronic control unit. It is impossible to adjust a corner of an advancing of ignition.


Precautions at work with system toplivopodachi/injection

At work with system toplivopodachi/injection it is necessary to observe the following rules:

1. Carefully clear places of connections and areas adjoining to them before separation.

2. After removal of components combine them in a pure place and cover with a film or paper. Do not cover a detail with rags!

3. The opened or disassembled components are necessary for covering or isolating accurately if their repair cannot be carried out immediately.

4. Establish only pure details.

  – develop the packed spare parts only before the installation

  – do not use spare part which were stored not packed (for example, in a box for tools)

5. At open fuel system:

  – avoid use of the compressed air where it is possible

  – do not move the car without emergency