Audi 80/90/Coupe

since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburetors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Ignition system
- 8. Transmission
   8.1.2. A fork - the main cylinder of coupling
   8.1.3. Press coupling disk
   8.1.4. Malfunctions of coupling
   + 8.2. Mechanical transmission 012
   + 8.3. Mechanical transmission 01А
   - 8.4. Automatic transmission 089
      8.4.2. Lever and rope of the lever of gear shifting
      8.4.3. Lock of automatic gear shifting
      8.4.4. Mechanism of management of a butterfly valve
      8.4.5. Removal and transmission installation
      8.4.6. Check of the moments of gear shifting
      8.4.7. Main transfer
      8.4.8. Differential
   + 8.5. Automatic transmission 087
   8.6. Dismantling and assembly of automatic transmissions
   8.7. Block of valves
   + 8.8. Automatic transmission 097
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
+ 12. Body, salon
+ 13. Central air
+ 14. Electric equipment







dfe5d7b3


8.4.2. Lever and rope of the lever of gear shifting

GENERAL INFORMATION

Switching lever gear shifting transfers / Rope

1. Plug
2. Spring
3. Arm of the lever of gear shifting
put an AKD 512001 hermetic layer between an arm and a transmission casing at installation
4. Casing of the lever of gear shifting
5. The locking solenoid of automatic gear shifting
6. Arm of a rope of switching
7. Sealing ring
8. Lock ring
9. Gear shifting rope
10. Angular arm of a rope of switching
11. Cover
12. Switch of bulbs of neutral, parking transfers and backing transfer
13. 8 N of m.
14. Rope clip
15. The switching lever
16. Coupling
17. Plug
18. Lock ring
19. Spring
20. Centering pin
21. Gear shifting lever
22. Plug

Prevention

Before the work beginning with working engine, always move the gear shifting lever to situation P (parkings) and put the car on the hand brake.

Disconnect a wire of the negative plug of the accumulator before the work beginning with any of elements of system of electric equipment.

It is necessary to press a brake pedal before the lever of gear shifting can be removed from parking transfer.

Do not bend and do not overwind a rope. Grease the rope ends before installation.


Installation / adjustment

PERFORMANCE ORDER
1) tighten rope fastening on a rope arm to 15 N of m.
2) establish a rope in a clip for a rope before installation of an angular arm
3) move the gear shifting lever to situation P
4) weaken a nut of a clip of a rope
5) move switching lever to situation P (back against the stop)
6) tighten a nut of a clip of a rope to 8 N of m.

Mechanism of the lever of gear shifting and gear shifting rope

1. Handle of the lever of gear shifting
2. Casing of the lever of gear shifting
establish designation of R forward
establish after adjustment of the electromagnetic switch
3. Electromagnetic switch
4. Cover
5. 5 N of m.
6. Torsionny spring
7. Plug
8. Washer
9. Lever switch
gear shiftings
check: the engine should be started, when the lever
switchings is
in situation P or N
headlights of a backing should light up at inclusion of transfer of a backing.
If is not present, turn the switch in a nest and again check its work
10. Basis
at installation put an A/CD 512 001 hermetic layer between the basis and a body
11. Clip bolt
12. Arm
13. Lock ring
14. Rope of the lever of gear shifting
with directing and the plug
grease the rope ends before installation, tighten a nut of fastening of a rope on an arm to 15 N of m.
check, that the going tube densely sat
for adjustment move the gear shifting lever in situation P
move switching lever on a transmission in situation P (against the stop back)
tighten a nut of a clip of a rope to 20 N of m.
15. Cover
16. Coupling
17. Washer
18. Plug
19. Coupling
20. Boss
21. Spring clamp
22. 20 N of m.
23. The switching lever
24. Washer
25. Plug
26. Compression spring
establish on the switching lever before installation of a directing pin
27. Plug
28. A directing pin
29. The gear shifting lever with a fork for lever locking in situation P or N

Prevention

Disconnect a wire of the negative plug of the accumulator before the work beginning with any of elements of electric equipment of the car.


Installation of an arm of the lever of gear shifting in relation to the gear shifting lever

PERFORMANCE ORDER
1) establish щуп And, thickness of 0.8 mm, between the lever of gear shifting and the electromagnetic switch
2) press the electromagnetic switch to щупу and tighten a fastening nut
3) after installation of the electromagnetic switch, establish on the center the bottom opening of a fork of the lever of gear shifting and submit tension on the switch
4) the pin of the solenoid will close a fork
5) establish a casing of the lever of gear shifting so that the lever of gear shifting was opposite to a mark N in a casing (neutral transfer)
6) establish the lever A by means of a pin or a drill

In = a pin, diameter of 4.0 mm, inserted into a casing opening
7) switch the gear shifting lever in situation in situation N
8) establish the switch so that fastening (it is specified by an arrow) was fixed on the gear shifting lever
9) tighten fastening bolts to 5 N of m.

10) remove a pin or a drill

After switch installation, check its work.