Audi 80/90/Coupe

since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburetors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Ignition system
- 8. Transmission
   8.1.2. A fork - the main cylinder of coupling
   8.1.3. Press coupling disk
   8.1.4. Malfunctions of coupling
   + 8.2. Mechanical transmission 012
   + 8.3. Mechanical transmission 01А
   + 8.4. Automatic transmission 089
   + 8.5. Automatic transmission 087
   8.6. Dismantling and assembly of automatic transmissions
   8.7. Block of valves
   + 8.8. Automatic transmission 097
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
+ 12. Body, salon
+ 13. Central air
+ 14. Electric equipment


dfe5d7b3



8.6. Dismantling and assembly of automatic transmissions

GENERAL INFORMATION

Assembly / dismantling of the main transfer 089
1. Regulator
2. Sealing ring
3. Clamping plate
should hold a speedometer drive reliably. If it is necessary, adjust installation or replace a plate
4. Gear wheel of a drive of a speedometer
5. Case of the main transfer
6. Starter plug
7. Differential
8. Bracket
9. Cap of a maslonalivny opening
10. Internal holder of the bearing of a leading gear wheel
11. S4 washer
note thickness
12. Leading gear wheel
together with a gear wreath
13. Sealing ring
14. Needle bearing of a regulator
15. Regulator epiploon

Dismantling / assembly of the main transfer 089
1. Epiploons of a leading gear wheel
2. 25 N of m.
3. Back cover
will a little believe at removal
4. A sealing ring (for the oil channel)
check persistent washers on existence of cracks and a gear wheel on existence of wear tracks
5. Sealing ring
check persistent washers on existence of cracks and a gear wheel on existence of wear tracks
6. External holder of the bearing of a leading gear wheel
7. Plug of epiploons
always replace uplotnitelnny rings
8. Internal holder of the bearing of a leading gear wheel
9. S3 washer
10. Sealing ring
check persistent washers on existence of cracks and a gear wheel on existence of wear tracks
11. Epiploon of a flange of a drive
12. 25 N of m.
13. Drive flange
14. External holder of the bearing of differential
for removal / installation the adjusting ring is necessary for heating up (approximately to 100 ° C)
15. Sealing ring
check persistent washers on existence of cracks and a gear wheel on existence of wear tracks
16. Spherical valve
17. 25 N of m.
18. Forward cover
put hermetic on adjoining surfaces
adjust installation of a conducting gear wheel at cover replacement
19. Epiploon of a leading gear wheel
20. External holder of the bearing of a leading gear wheel
21. Adjusting ring


Dismantling / assembly of the main transfer 087/089

1. Adjusting screw of a brake tape
2nd transfer
pressurize a carving by means of AKD 456 000 01 hermetic
2. Pusher of the adjusting screw
it is possible to replace only after valve removal
3. Transmission case
4. Piston of a brake tape of the 2nd transfer
5. Lock ring
6. Pump of okhladitelny liquid
7. Ring piston of the coupling of the 1st
backing transfers / transfers
8. Coupling of the 1st transfer / transfer
backing
9. A disk with springs
10. 7 N of m.
11. Brake tape of the 2nd transfer
12. Coupling of transfer forward / backing
13. Persistent washer
14. Washer
15. Needle bearing
establish with washers in the coupling
forward course
16. Washer
17. Coupling of a forward course
18. And golchaty bearing
19. Planetary transfer of a forward course
20. Dual central gear wheel
the short part is turned to planetary transfer
21. Cover

22. Persistent washer
23. External shpitsevy ring of the coupling of the 1st leredachi/backing transfers
24. Internal shpitsevy ring of the coupling of the 1st transfer / transfer of a backing
before installation sustain in охл. liquids machine gun. transmissions of 15 minutes
25. Persistent washer
uvulas should enter into openings of planetary transfer of a backing
26. Planetary transfer of a backing
27. Unilateral coupling
28. Lock shponka
get it after removal of the unilateral coupling
29. Lock ring
30. Persistent washer
uvulas should enter into openings of planetary transfer of a backing
31. Needle bearing
32. Cogwheel of planetary transfer of a backing
33. Laying
always replace
34. Razdelitelna plate
after installation check an axial gap of a box of transfers / the main transfer

Dismantling / assembly of the main transfer 087

1. Hydrotransformer epiploon
2. 35 N of m.
3. Cover of the main transfer
put hermetic on adjoining surfaces at installation
the channel of liquid of an automatic transmission should remain open
after replacement of a cover adjust installation of a leading gear wheel
4. Magnet
5. External holder of a conic roller bearing
6. Case of the main transfer
7. Regulator epiploon
edges of an epiploon it is turned to a regulator
8. Regulator
9. Sealing ring
always replace
10. Cover
11. 10 N of m.
12. Needle bearing of a regulator
13. External holder of a conic roller bearing
remove and establish only with a warm adjusting ring
14. Epiploon of a flange of a semi-axis
before installation fill
space between epiploon edges multipurpose greasing
it is possible to replace an epiploon without removing a transmission
15. Semi-axis flange
16. 25 N of m.
17. Sealing ring
always replace
18. Adjusting ring
when using old bearings, note the provision of installation of an adjusting ring before removal and use these marks at installation
19. Leading gear wheel
together with a gear wreath
20. Internal holder of a conic roller bearing
adjust installation of the leader
gear wheels after holder replacement
21. Epiploon plug
adjust installation of a leading gear wheel after epiploon replacement
22. External holder of a conic roller bearing
23. First epiploon of a leading gear wheel
24. 35 N of m.
25. Second epiploon of a leading gear wheel
26. Epiploon
27. Sealing ring
always replace
28. Cover of a leading gear wheel
adjust installation of a conducting gear wheel after cover replacement
29. Internal holder of a conic roller bearing
adjust installation of a conducting gear wheel after holder replacement
30. Adjusting washer of S3
31. Adjusting washer of S4
32. Clamp
33. Spring washer
34. 8 N of m.
35. Adjusting ring
establish together with a sealing ring, an epiploon of a flange of a semi-axis and an external holder of a conic roller bearing
36. Bolt
37. Sealing ring
always replace
38. Speedometer drive
39. Bracket
after installation the bracket should adjoin densely to a case, adjust or replace, if it is necessary
40. 8 N of m.
41. Differential
at installation of a new box, adjust installation of a gear wreath
42. Second epiploon of a leading gear wheel
remove by means of the VW 681 tool
43. First epiploon of a leading gear wheel
remove by means of the VW 681 tool
44. Sealing ring of the oil channel
always replace