Audi 80/90/Coupe

since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburetors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Ignition system
- 8. Transmission
   8.1.2. A fork - the main cylinder of coupling
   8.1.3. Press coupling disk
   8.1.4. Malfunctions of coupling
   + 8.2. Mechanical transmission 012
   + 8.3. Mechanical transmission 01А
   + 8.4. Automatic transmission 089
   + 8.5. Automatic transmission 087
   8.6. Dismantling and assembly of automatic transmissions
   8.7. Block of valves
   - 8.8. Automatic transmission 097
      8.8.2. Lever and rope of the lever of gear shifting
      8.8.3. Lock of automatic gear shifting
      8.8.4. Removal and transmission installation
      8.8.5. Block of valves
      8.8.6. Differential and gear wheels
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
+ 12. Body, salon
+ 13. Central air
+ 14. Electric equipment







dfe5d7b3


8.8.2. Lever and rope of the lever of gear shifting

GENERAL INFORMATION

Perklyucheniye lever gear shifting transfers / Rope


1. Cover
2. Program switch (Е122)
3. Casing of the lever of gear shifting
усанавливайте designation of the parking
transfers forward
establish after adjustment
electromagnetic switch
4. Handle of the lever of gear shifting
5. 9 N of m.
6. Washer
7. Solenoid of the lock of gear shifting
(No. 110)
8. 10 N of m.
9. Torsionny spring
10. Gear shifting lever
with a fork for lever short circuit in situation P and N
11. Plug of a torsiony spring
12. A directing pin
establish after installation of a kompressionny spring
13. Kompressionny spring
establish on the gear shifting lever
before installation of a directing pin
14. Lock ring
15. Washer
16. Basis
put an AKD 512 001 05 hermetic layer between the basis and a body
establish bolts and fastening washers (the moment
inhalings of 10 N of m)
17. Plug
18. Washer
19. The switching lever
20. Coupling
21. Nut
moment of an inhaling of 20 N of m.
22. Washer
23. Plug
24. Coupling
25. Washer
26. Boss
27. Cover
replace if it is necessary
check accuracy of installation, that moisture not
got on a rope of the lever of gear shifting
28. 23 N of m.
29. Clip

30. Transmission fastening
with fastening of a rope of gear shifting
31. 40 N of m.
32. Gear shifting rope
with the directing plug
grease the rope ends before installation
do not bend and do not overwind a rope
for adjustment:
преключите the gear shifting lever in situation P
weaken a nut on a rope clip
move up the lever on a transmission in situation P (against the stop back)
after that, when the rope is in a loose condition, tighten a nut (21) to 20 N of m.
after adjustment of a rope check operation of the switch of the lever of an adventure of transfers and adjust it if it is necessary
33. Arm of a rope of the lever of gear shifting
34. Clip screw
35. Clip
36. 5 N of m.
37. Switch of the lever of gear shifting
check:
the engine should be started only when the lever of gear shifting is in situation P or N
headlights of a backing should join at inclusion of transfer of a backing
if is not present, turn the switch in a nest and again провверьте its work
38. Plug

Installation of an arm of the lever of gear shifting in relation to the gear shifting lever

PERFORMANCE ORDER
1) transfer the gear shifting lever to situation R

And – щуп for measurement of gaps in thickness of 1.0 mm
2) establish щуп between the lever of gear shifting and the electromagnetic switch
3) press the electromagnetic switch to щупу and tighten a fastening nut
4) establish on the center the bottom opening of a fork of the lever of gear shifting and submit tension on the switch
5) the pin of the solenoid will close a fork
6) establish a casing of the lever of gear shifting so that the lever of gear shifting was opposite to a mark N in a casing
7) the lever of gear shifting should pass identical distance between provisions N and D and provisions N and R
8) establish the lever A by means of a pin or a drill

In (diameter of 4.0 mm), inserted into a casing opening

Switch of the lever of gear shifting, installation

PERFORMANCE ORDER
1) switch the gear shifting lever in situation in situation N
2) establish the switch so that fastening (it is specified by an arrow) was fixed on the gear shifting lever
3) tighten fastening bolts to 5 N of m.
4) remove a pin or a drill

After switch installation, check its work.